GB350S

Instruments

Display Check

When the ignition switch is turned to (On) position, the speedometer needle swings to the maximum scale on the dial once, all the digital segments will show.

If any part of these displays does not come on when it should, have your dealer check for problems.

  • Speedometer

    • This shows your speed in kilometer per hour (km/h) and/or miles per hour (mph) depend on type.

  • Odometer [TOTAL], Tripmeter [TRIP A/B], Current fuel mileage, Average fuel mileage [AVG], Available driving distance [RANGE], and Battery voltage[]
  • Fuel gauge

    • Remaining fuel when only 1st (E) segment starts flashing: approximately 1.5 L (0.40 US gal, 0.33 Imp gal)

    NOTICE

    You should refuel when the reading approaches the 1st (E) segment. Running out of fuel can cause the engine to misfire, damaging the catalytic converter.

    If the fuel gauge indicator flashes in a repeat pattern or turns off:

  • Clock (12-hour display)

    • To set the clock:

  • Gear position indicator

    • The gear position indicator shows the gear position.

  • “-” appears when the transmission is not shifted properly.
  • SET button
  • SEL button


    • Odometer [TOTAL], Tripmeter [TRIP A/B], Current fuel mileage, Average fuel mileage [AVG], Available driving distance [RANGE], and Battery voltage[]

    Press the SEL button to select the odometer, tripmeter A, tripmeter B, current fuel mileage, average fuel mileage, available driving distance, and battery voltage.

    Battery voltage

    Available driving distance

    Average fuel mileage

    Current fuel mileage

    Tripmeter A

    Odometer

    Tripmeter B

    Odometer [TOTAL]

    Total distance ridden.

    When “------” is displayed, go to your dealer for service.


    Tripmeter [TRIP A/B]

    Distance ridden since tripmeter was reset.

    When “----.-” is displayed, go to your dealer for service.

    To reset the tripmeter:

    Current fuel mileage

    The current fuel mileage is displayed with the unit of “km/L” or “L/100 km”.

    Display range: 0.0 to 99.9 km/L (or L/100 km)

  • When the vehicle speed is below 7 km/h (4 mph), it displays “--.-”


    • When “--.-” is displayed except for above-mentioned cases, go to your dealer for service.


    E type only

    If the “mile” for mileage is selected, the current fuel mileage is displayed with the unit of “mile/gal” or “mile/L”.

    Display range: 0.0 to 299.9 mile/gal or 0.0 to 99.9 mile/L

  • When the vehicle speed is below 5 mph (8 km/h), it displays “---.-”

    • Average fuel mileage [AVG]

    The average fuel mileage based on tripmeter A is displayed with the unit of “km/L” or “L/100 km”.

    Display range: 0.0 to 99.9 km/L (or L/100 km)

  • Initial display: “--.-” is displayed.
  • When the tripmeter A is reset: “--.-” is displayed.


    • When “--.-” is displayed except for above-mentioned cases, go to your dealer for service.


    E type only

    If the “mile” for mileage is selected, the average fuel mileage based on tripmeter A is displayed with the unit of “mile/gal” or “mile/L”.

    Display range: 0.0 to 299.9 mile/gal or
    0.0 to 99.9 mile/L


    To reset the Average fuel mileage:

    Available driving distance [RANGE]

    Displays the estimated distance you can travel on remaining fuel.

    The indicated available driving distance is calculated based on the remaining fuel.

    According to the driving condition, the indicated figure may not always be the actual available distance.

    Display range: 999 to 5 km

    E type only

    Display range: 999 to 3 mile


  • Above 999 km: “999” is displayed.

    • E type only

  • Above 999 mile: “999” is displayed.


  • Initial display: “---” is displayed.
  • When the calculated distance is below 5 km (3 mile) or the amount of remaining fuel is below 1.0 L (0.26 US gal, 0.22 Imp gal): “---“ is displayed.


    • When “---” is displayed except for the above-mentioned cases, go to your dealer for service.


    Battery voltage []

    Displays current battery voltage.

    To reset the tripmeter

    When you reset the tripmeter A, average fuel mileage is also reset.

    To reset the tripmeter A and average fuel mileage, press and hold the SEL button while tripmeter A is displayed.

    To reset the tripmeter B, press and hold the SEL button while tripmeter B is displayed.

    Setting mode

    Following items can be changed sequentially.

  • ECO indicator setting
  • Clock setting
  • Backlight brightness adjustment
  • E type only Changing of mileage unit
  • Changing of fuel mileage meter unit


    • The control is automatically switched from the setting mode to the ordinary display if the switch is not pressed for about 30 seconds.

    In this case, undecided settings will not be maintained.

    The being selected setting can also be set by turning the ignition switch to the (Off) position.

    Ordinary display

    Setting mode

    Backlight brightness adjustment

    Clock setting

    ECO indicator setting

    Changing of mileage unit

    E type only

    Changing of fuel mileage meter unit

    Press and hold the SEL button and the SET button

    Press the SET button


    1 ECO indicator setting

    You can switch the ECO indicator on or off.

    ECO indicator

  • Turn the ignition switch to the (On) position.
  • Press and hold the SEL button and the SET button until the ECO indicator starts flashing.
  • Press the SEL button to select “On” (activate) or “OFF” (deactivate).
  • Press the SET button. The ECO indicator is set, and then the display moves to the clock setting.


    • 2 Clock setting

  • Press SEL button until the desired hour is displayed.
  • Press and hold the SEL button to advance the hour fast.
  • Press the SET button. The minute digits start flashing.
  • Press SEL button until the desired minute is displayed.
  • Press and hold the SEL button to advance the hour fast.
  • Press the SET button. The clock is set, and then the display moves to the backlight brightness adjustment.


    • 3 Backlight brightness adjustment

    You can adjust the backlight brightness to one of the five levels.

  • Press the SEL button to select the backlight brightness.
  • Press the SET button. The backlight brightness is set.

    • ED type only

    The display moves to the changing of fuel mileage meter unit.

    E type only

    The display moves to the changing of mileage unit.


    4 Changing of mileage unit

    E type only

  • Press the SEL button to select “mile” or “km”.
  • Press the SET button. The mileage unit is set, and then the display moves to the changing of fuel mileage meter unit.


    • 5 Changing of fuel mileage meter unit

  • Press the SEL button to select “km/L” or “L/100 km”.

    • E type only

    If the “mile” for mileage is selected, press the SEL button to select “mile/gal” or “mile/L”.

  • Press the SET button. The fuel mileage meter unit is set, and then the display returns to the ordinary display.

    • Recommended topic(s)

  • Engine Oil
  • Battery
  • Fuses