Instruments
The display type consists of the following 5 patterns.
Each display type has the SPORT mode.
The operation of the instrument is mainly explained in the ANALOG display type.
Factory default setting is ANALOG.
Do not operate the display functions for a long time with the engine stopped. It may result in a low (or dead) battery.
STD mode display
Display type: ANALOG (Factory default setting)
NOTICE |
(excessive engine rpm range)
The red zone changes low coolant temperature mode.
Display type: DIGITAL
NOTICE |
(excessive engine rpm range)
The red zone changes low coolant temperature mode.
Display type: BAR
NOTICE |
(excessive engine rpm range)
The red zone changes low coolant temperature mode.
Display type: NO REV
The tachometer is not displayed when NO REV is selected.
Display type: PRACTICE
NOTICE |
(excessive engine rpm range)
The red zone changes low coolant temperature mode.
To change to the SPORT mode display: Set the “LAP” to “ON” in setting mode.
When switching to SPORT mode display, the following message appears on the screen for a few seconds then the lap timer is displayed.
When in the SPORT mode, the PASSING/LAP switch functions as a LAP switch.
Display type:
DIGITAL
Display type:
NO REV
Display type:
ANALOG
Display type:
BAR
Display type:
PRACTICE
The engine rpm is limited to 8,000 r/min (rpm) to protect the engine when the coolant temperature is below 70°C.
In the low coolant temperature mode, running at 8,000 r/min (rpm) or lower is recommended.
In the low coolant temperature mode, the pop-up information is displayed. Also start of the red zone changes to 8,000 r/min (rpm).
Display type:ANALOG
Tachometer red zone
Pop-up information
Display type:DIGITAL
Pop-up information
Tachometer red zone
Display type:BAR
Pop-up information
Tachometer red zone
Display type:NO REV
Pop-up information
Display type:PRACTICE
Pop-up information
Tachometer red zone
The display will return to the STD mode in the following cases.
The operating functions depend on the ABS mode selected.
ABS1 (RACE) and ABS2 (TRACK) are suitable for sports riding on a closed course.
ABS (STANDARD) is suitable for normal riding on a public road.
ABS mode setting
ABS mode |
ABS RR |
Honda RR LIFT CONTROL |
Honda CORNERING ABS CONTROL |
ABS1 (RACE) |
OFF |
OFF |
OFF |
ABS2 (TRACK) |
ON |
OFF |
ON |
ABS (STANDARD) |
ON |
ON |
ON |
Turns the ABS function on the rear wheel ON or OFF (toggle).
When the ABS RR is OFF, the ABS function on the rear wheel is disabled.
Honda RR LIFT CONTROL:
When ON, this function reduces the risk of a rear wheel lifting when braking by using ABS brake control.
Honda CORNERING ABS CONTROL:
When ON, this function can help stabilize the vehicle while cornering by using ABS brake control.
When select the ABS1 (RACE) or ABS2 (TRACK) in the setting mode, the following message is displayed.
or |
If the ABS mode has been set to ABS1 (RACE) or ABS2 (TRACK), the following message is displayed when the electrical system is turned on.
or |
If you start riding without selecting the "Change to ABS (STANDARD)" or "OK", the current ABS mode will be maintained.
Basic Operations
You can operate and set the various functions of the display using the switches on the left handlebar.
PASSING/LAP switch
Sel down switch
Sel up switch
Sel left/right switch
MODE switch
When switching or setting the display, refer to the switch operation guide is displayed.
Switch operation guide |
Type of the switch operation guide: | ||
|
: |
Press the |
|
: |
Press the |
|
: |
Push the |
|
: |
Push the |
|
: |
Press and hold the |
|
: |
Press and hold the |
|
: |
Push and hold the |
|
: |
Push and hold the |
To switch the INFO area
To change the page of the INFO area, push the
sel left/right switch.
You can change the information items to be displayed on the pages 1-3 (INFO 1-3).
You can also change the number of items to be displayed in the information area.
To select the FAVORITE INFORMATION
To change the number of information items are displayed
Page 4 displays the current riding mode settings.
Page 1 (INFO 1)
Page 2 (INFO 2)
Page 3 (INFO 3)
Page 4 (Riding mode)
CBR1000SP Quick Shifter indicator
The following items are types of information that can be displayed on pages 1-3 (INFO 1-3).
Total distance ridden.
|
When “------” is displayed, go to your dealer for service.
Distance ridden since the tripmeter was reset.
|
When “----.-” is displayed, go to your dealer for service.
Tripmeter A fuel consumption [TRIP A CONS.]
Displays the tripmeter A fuel consumption since the tripmeter A was reset.
Display range: 0.0 to 299.9 L (litres) or 0.0 to 299.9 GAL (gallon)
|
When “---.-” is displayed go to your dealer for service.
Tripmeter A fuel consumption is reset when you reset tripmeter A.
Current fuel mileage [INST. CONS.]
Displays the current instant fuel mileage.
Display range: 0.0 to 299.9 L/100km (km/L, mile/gal or mile/L)
|
When “---.-” is displayed except for the above-mentioned cases, go to your dealer for service.
Average fuel mileage [AVG. CONS.]
Displays the average fuel mileage since the average fuel mileage was reset.
Display range: 0.0 to 299.9 L/100km (km/L, mile/gal or mile/L)
|
When “---.-” is displayed except for the above-mentioned cases, go to your dealer for service.
To reset the average fuel mileage
Displays the average speed since the average speed was reset.
Display range: 0 to 350 km/h (0 to 218 mph)
|
When “---” is displayed except for the above-mentioned cases, go to your dealer for service.
Displays the engine operating time since the elapsed time was reset.
Display range: 00:00 to 99:59 (hours:minutes)
|
When “--:--” is displayed, go to your dealer for service.
Numerical tachometer display [REV]
Displays the engine revolutions per minutes.
Display range: 0 to 16,500 r/min
Above 16,500 r/min (rpm): “16500” is displayed.
|
Throttle grip angle [GRIP ANGLE]
Displays the throttle grip angle during operation.
Display range: 0 to 90 deg
|
When “--” is displayed, go to your dealer for service.
Displays the current voltage.
|
Show the date of today.
|
Display range:
Day of the week: MON to SUN
DAY: 1 to 31
MONTH: JAN to DEC
YEAR: 2023 to 2099
Displays the characters of user's choice.
|
Displays the CBR logo.
|
Shift indicator set value [SHIFT POINT]
Displays the shift indicator set value.
Display range: 5,000 - 16,500 r/min
|
Lap fuel consumption [LAP CONS.]
Displays the fuel consumption of the latest lap.
Display range: 0.0 to 50.0 L (litres) or 0.0 to 50.0 GAL (gallon)
|
When “--.-” is displayed except for the above-mentioned cases, go to your dealer for service.
Lap average fuel mileage [LAP AVG. CONS.]
Displays the average fuel mileage of the latest lap.
Display range: 0.0 to 299.9 L/100km (km/L, mile/gal or mile/L)
|
When “---.-” is displayed except for the above-mentioned cases, go to your dealer for service.
Lap average speed [LAP AVG. SPD.]
Displays the average speed of the latest lap.
Display range: 0 to 350 km/h (0 to 218 mph)
|
When “---” is displayed except for the above-mentioned cases, go to your dealer for service.
Maximum acceleration in this time [MAX ACC.]
Displays the maximum acceleration since the engine was started.
Display range: 0 to 1.5 G
When the electrical system is turned off, the maximum acceleration is reset.
|
Maximum deceleration in this time [MAX DEC.]
Displays the maximum deceleration since the engine was started.
Display range: 0 to 1.5 G
When the electrical system is turned off, the maximum deceleration is reset.
|
Maximum right lean angle in this time [MAX LEAN ANGLE R]
Displays the maximum lean angle of right side since the engine was started.
Display range: 0 to 60 deg
When the electrical system is turned off, the maximum lean angle of right is reset.
|
Maximum left lean angle in this time [MAX LEAN ANGLE L]
Displays the maximum lean angle of left side since the engine was started.
Display range: 0 to 60 deg
When the electrical system is turned off, the maximum lean angle of left is reset.
|
Fuel consumption in this time [FUEL CONS.]
Displays the fuel consumption since the engine was started.
Display range: 0.0 to 50.0 L (litres) or 0.0 to 50.0 GAL (gallon).
When the electrical system is turned off, the fuel consumption is reset.
|
When “--.-” is displayed except for the above-mentioned cases, go to your dealer for service.
Average fuel mileage in this time [AVG. CONS. ]
Displays the average fuel mileage since the engine was started.
Display range: 0.0 to 299.9 L/100km (km/L, mile/gal or mile/L).
When the electrical system is turned off, the average fuel mileage is reset.
|
When “---.-” is displayed except for the above-mentioned cases, go to your dealer for service.
Average speed in this time [AVG. SPD. ]
Displays the average speed since the engine was started.
Display range: 0 to 350 km/h (0 to 218 mph).
When the electrical system is turned off, the average speed is reset.
|
When “---” is displayed except for the above-mentioned cases, go to your dealer for service.
Elapsed time in this time [ELAPSED ]
Displays the engine operating time since the engine was started.
Display range: 00:00 to 99:59 (hours:minutes)
When the electrical system is turned off, the elapsed time is reset.
|
When “--:--” is displayed except for the above-mentioned cases, go to your dealer for service.
Intake air temperature [INTAKE AIR]
Display the intake air temperature.
Display range: -20.0 to 79.9°C
|
When “---.-” is flashes, go to your dealer for service.
Display the blank.
To Reset the Information
Select the page (INFO1, 2, 3) of INFO area that contains the item you want to reset with the
sel left/right switch.
Push and hold the of the
sel left/right switch until the RESET turns to red.
Select the item with the
sel left/right switch.
Push and hold the of the
sel left/right switch until the item is reset.
To exit the reset mode, push and hold the of the
sel left/right switch.
Displays the current lean angle of left/right side.
Displays the current acceleration/deceleration.
|
When the low fuel indicator appears the available driving distance and amount of remaining fuel displayed.
Remaining fuel amount turned to the reserve fuel mode: 3.2 L (0.8 US gal, 0.7 Imp gal)
NOTICE You should refuel when display is switched to reserve fuel mode. Running out of fuel can cause the engine to misfire, damaging the catalytic converter. |
Low fuel indicator Available driving distance Remaining fuel |
After refuelling more than the reserve amount, the display returns to normal when the electrical system has been on for about a minute.
Available driving distance (Only reserve fuel mode)
When the low fuel indicator lights, the estimated available driving distance is indicated.
Display range: 99 to 5 km or 99 to 3 mile
The indicated available driving distance is calculated based on the driving states, and the indicated figure may not always be the actual allowable distance.
When “--” is displayed except for the above-mentioned cases, go to your dealer for service.
Amount of remaining fuel (Only reserve fuel mode)
When the low fuel indicator lights, the estimated amount of remaining fuel can be selected.
Display range: 3.2 to 1.0 L (litres) or 0.7 to 0.2 GAL (gallon)
The amount of remaining fuel is calculated based on the driving states. The indicated amount of remaining fuel may be different from the actual amount.
When “-.-” is displayed except for the above-mentioned cases, go to your dealer for service.
Display range: 35°C to 132°C
In the following cases, pop-up information is displayed.
When the inspection time of your vehicle is approaching.
When your vehicle has helpful information.
When in the start mode.
CBR1000SP
When your vehicle has a problem with the ÖHLINS Smart EC system.
When your vehicle has multiple pieces of information, the high-priority pop-up information display will appear.
If the priorities are the same, pop-up information display appears alternately.
The priority order is as follows:
Priority |
Pop-up information items | |
1 |
| |
2 |
| |
3 |
| |
4 |
|
|
|
|
Maintenance Information
Indication |
Explanation |
Remedy |
|
When the periodic inspection time of your vehicle is approaching. |
Have your vehicle inspected by your dealer. |
|
When the oil change time of your vehicle is approaching. |
Change the engine oil. |
Helpful Information
Indication |
Explanation |
Remedy |
|
When the side stand is down. |
Raise the side stand. |
|
CBR1000SP |
Stop your vehicle. Wait for a few seconds until the indication turns off. If the indication dose not turns off, contact your dealer. |
|
When the coolant temperature below 70°C. |
Warm up the engine until the coolant temperature above 70°C. |
Start Mode Information
Indication |
Explanation |
Remedy |
|
When the background colour is: Orange: Start mode is allowed. Green: Limiting the engine revolution. Gray: Start mode is not allowed. |
Failure Information
Indication |
Explanation |
Remedy |
|
CBR1000SP |
Reduce speed and have your vehicle inspected by your dealer as soon as possible. |
The gear position is shown in the gear position indicator.
Displays the current ABS mode.
ABS1, ABS2 or blank (ABS (STANDARD)) is displayed.
When the indicator flashes, go to your dealer for service.
If it comes on while engine is running:
If it comes on while engine is running:
High coolant temperature indicator
CBR1000SP
Displays the current status of the Quick Shifter.
This indicator is displayed when the INFO area is in page 4 (Riding mode).
|
Quick Shifter system is disabled. |
|
Quick Shifter upshifting is enabled. |
|
Quick Shifter downshifting is enabled. |
|
Quick Shifter upshifting and downshifting are both enabled. |
Lap Timer
You can record lap time in the SPORT mode.
Previous lap time
Number of laps
Stopwatch/difference with the best lap
You can check and clear the recorded lap data in the setting mode.
Best icon
(Displayed when the fastest lap time displayed.)
Time stamp
Lap time
Lap number
User letter
Maximum deceleration
Maximum right lean angle
Maximum acceleration
Maximum left lean angle
Average fuel mileage
Maximum engine revolutions
Maximum coolant temperature
Fuel consumption
Average speed
Maximum vehicle speed
The lap data include the following:
Lap data |
Display range |
Previous lap number |
0 to 99 |
Previous lap time |
00'00"00 to 99'59"99 |
Stopwatch |
00'00"00 to 99'59"99 |
Difference with the best lap |
-99'59"99 to 00'00"00 to +99'59"99 |
Maximum vehicle speed |
0 to 350 km/h (0 to 218 mph) |
Average speed |
0 to 350 km/h (0 to 218 mph) |
Fuel consumption |
0.0 to 299.9 L (litres) or 0.0 to 299.9 GAL (gallon) |
Maximum coolant temperature |
35 to 132°C |
Average fuel mileage |
0.0 to 299.9 L/100km (km/L, mile/gal or mile/L) |
Maximum engine revolutions |
0 to 16500 r/min (rpm) |
Maximum acceleration |
0 to 1.5 G |
Maximum deceleration |
0 to 1.5 G |
Maximum right lean angle |
0 to 60 deg |
Maximum left lean angle |
0 to 60 deg |
To Measure the Lap Time
PASSING/LAP switch |
Stopwatch |
After 10 seconds, the display will return to the stopwatch.
Previous lap time Difference with the best lap Number of laps |
To restart the measurement
Press the PASSING/LAP switch again. The stopwatch restarts measurement.
To Check or Clear the Lap Time
Select the “LAP DATA” menu in the setting mode.
Recommended topic(s) |
---|
|
|
|