Your vehicle is equipped with a multi-information display that presents various functions and settings.
The multi-information display is a touch screen. You can operate by touching the screen.
When the ignition switch is turned 
(On), the Notice message appears on the screen for a few seconds.
Read the Notice message, and then press the ENT switch or touch [OK] on the screen.
|
|
Home Screen
From this screen, you can go to various functions and setup options.
|
|
Riding Information
You can go back to the riding information.
Riding information has 3 displays, Gold image display, Silver image display and Bronze image display.
These displays are switched according to riding mode.
To change the display setting on each riding mode
Phone
You can make calls using a Bluetooth® connected Bluetooth® audio devices.
Media
You can play music from Bluetooth® devices.
Settings
You can select various settings.
Riding Information
|
NOTICE Do not operate the engine in the Tachometer red zone. Excessive engine speed can adversely affect engine life. |
Handle grip heater status icon CRF1100A3/A4/D3/D4/DL4The handle grip heater status icon will appear while the handle grip heater is on.
If the handle grip heater status icon flashes:
(excessive engine rpm range)
CRF1100A/A3/A4
The gear position is shown in the gear position indicator.
CRF1100D/D3/D4/DL4
The gear position is shown in the gear position indicator.
The indicator may flash if:
This is normal. To operate the system again, turn the ignition switch to the 
(Off) position, and then to the 
(On) position again.
D is shown in the gear position indicator when the D mode is selected in the AT MODE.
S is shown in the gear position indicator when the S mode is selected in the AT MODE.
If the “-” indicator is blinking in the gear position window while riding:
Fuel gaugeRemaining fuel when only E (1st) segment starts flashing:
Approximately 3.6 L (0.95 US gal, 0.79 Imp gal) CRF1100A/A3/D/D3
Approximately 3.9 L (1.03 US gal, 0.86 Imp gal) CRF1100A4/D4/DL4
If the fuel gauge indicator flashes:
|
NOTICE You should refuel when the reading approaches the E (1st) segment. Running out of fuel can cause the engine to misfire, damaging the catalytic converter. |
|
|
Coolant temperature gaugeWhen the coolant is over specified temperature, all segments turn red and the H (6th) segment flashes and high coolant temperature indicator lamps.
If the coolant temperature gauge indicator flashes:
|
|
When the indicator flashes, have your dealer check for problems.
When the indicator flashes, have your dealer check for problems.
When the indicator flashes, have your dealer check for problems.
The speed set for cruise control is displayed.
When the indicator flashes, have your dealer check for problems.
When the indicator flashes, have your dealer check for problems.
When the indicator flashes, have your dealer check for problems.
Handle grip heater status icon CRF1100A3/A4/D3/D4/DL4The handle grip heater status icon will appear while the handle grip heater is on.
If the handle grip heater status icon flashes:
|
NOTICE Do not operate the engine in the Tachometer red zone. Excessive engine speed can adversely affect engine life. |
(excessive engine rpm range)
The speed set for cruise control is displayed.
Fuel gaugeRemaining fuel when only E (1st) segment starts flashing:
Approximately 3.6 L (0.95 US gal, 0.79 Imp gal) CRF1100A/A3/D/D3
Approximately 3.9 L (1.03 US gal, 0.86 Imp gal) CRF1100A4/D4/DL4
If the fuel gauge indicator flashes:
|
NOTICE You should refuel when the reading approaches the E (1st) segment. Running out of fuel can cause the engine to misfire, damaging the catalytic converter. |
|
|
When the indicator flashes, have your dealer check for problems.
When the indicator flashes, have your dealer check for problems.
When the indicator flashes, have your dealer check for problems.
When the indicator flashes, have your dealer check for problems.
When the indicator flashes, have your dealer check for problems.
Handle grip heater status icon CRF1100A3/A4/D3/D4/DL4The handle grip heater status icon will appear while the handle grip heater is on.
If the handle grip heater status icon flashes:
|
NOTICE Do not operate the engine in the Tachometer red zone. Excessive engine speed can adversely affect engine life. |
(excessive engine rpm range)
Fuel gaugeRemaining fuel when only E (1st) segment starts flashing:
Approximately 3.6 L (0.95 US gal, 0.79 Imp gal) CRF1100A/A3/D/D3
Approximately 3.9 L (1.03 US gal, 0.86 Imp gal) CRF1100A4/D4/DL4
If the fuel gauge indicator flashes:
|
NOTICE You should refuel when the reading approaches the E (1st) segment. Running out of fuel can cause the engine to misfire, damaging the catalytic converter. |
|
|
When the indicator flashes, have your dealer check for problems.
When the indicator flashes, have your dealer check for problems.
When the indicator flashes, have your dealer check for problems.
The speed set for cruise control is displayed.
Basic Operations
You can operate and set the various functions of your vehicle using the switches on the left handlebar and 
function sel switch on the right handlebar or touch screen.
However, you cannot operate some functions while the vehicle is in motion.
|
|
Pull backward and hold the 
page switch on the left handlebar or touch the clock area of the multi-information display with your vehicle stopped.
|
|
To Select a Desired Setting Menu
To operate with the left handlebar:
Press 
or 
to select the available choices.
To operate with the left handlebar:
Push 
or 
to select the available choices.
|
|
To operate with the touch screen:
Touch the menu to be selected on the touch screen.
To operate with the left handlebar:
Press the ENT switch on the left handlebar to set your selection.
|
ENT switch |
To operate with the touch screen:
Touch the menu to be selected on the touch screen.
To return to the riding information:
Pull backward the page switch on the left handlebar.
To return to the Home screen:
Pull backward and hold the page switch on the left handlebar.
To return the previous screen:
Press the 
back switch on the left handlebar.
|
|
To operate with the touch screen:
Touch the to be selected on the touch screen.
Also, the setting mode ends when your vehicle speed reaches approximately 6 km/h (4 mph).
Page 1:
Page 1 shows the following items: Tripmeter A [TRIP A] and three items related to Tripmeter A [TRIP A] and Tripmeter B [TRIP B].
|
|
Page 2:
Page 2 shows the following items: Tripmeter B [TRIP B] and three items related to Tripmeter B [TRIP B].
|
|
Page 3:
Page 3 shows four items selected from the following items.
|
|
Page 4:
Page 4 shows the setting values of the following items.
Rear suspension preload level [PRELOAD] display
G switch [G] display
|
|
To Switch the Page of Display
or of the sel left/right switch until the desired page is displayed.You can also perform the above settings by using the touch screen.
To Switch the Page 1 or Fuel Gauge
or of the sel left/right switch to switch the page or fuel gauge.Tripmeter A [TRIP A]
Distance ridden since the tripmeter A was reset.
|
|
When “----.-” flashes, have your dealer check for problems.
To reset the tripmeter A [TRIP A]:
Tripmeter A Average Fuel Mileage [AVG. CONS.]
Displays the average fuel mileage since the tripmeter A was reset.
The average fuel mileage will be calculated based on the value displayed on the selected tripmeter A.
Display range: 0.0 to 299.9 l/100 km (km/l, mpg or mile/L)
|
|
When “---.-” flashes, have your dealer check for problems.
To reset the tripmeter A average fuel mileage [AVG. CONS.]:
Tripmeter A Average Speed [AVG. SPD.]
Displays the average speed since the tripmeter A was reset.
The average speed will be calculated based on the value displayed on the selected tripmeter A.
Display range: 0.0 to 299.0 km/h or 0.0 to 186.0 mph
|
|
To reset the tripmeter A average speed [AVG. SPD.]:
Tripmeter A Fuel Consumption [CONS.]
Displays the tripmeter A fuel consumption since the tripmeter A was reset.
Display range: 0.0 to 300.0 L (gal)
|
|
To reset the tripmeter A fuel consumption [CONS.]:
Tripmeter A Elapsed [ELAPSED]
Displays the tripmeter A elapsed since the tripmeter A was reset.
Display range: 00:00 to 99:59 (hours:minutes)
|
|
When “00:00” flashes, have your dealer check for problems.
To reset the tripmeter A elapsed [ELAPSED]:
Tripmeter B [TRIP B]
Distance ridden since the tripmeter B was reset.
|
|
When “----.-” flashes, have your dealer check for problems.
To reset the tripmeter B [TRIP B]:
Tripmeter B Average Fuel Mileage [AVG. CONS.]
Displays the average fuel mileage since the tripmeter B was reset.
The average fuel mileage will be calculated based on the value displayed on the selected tripmeter B.
Display range: 0.0 to 299.9 l/100 km (km/l, mpg or mile/L)
|
|
When “---.-” flashes, have your dealer check for problems.
To reset the tripmeter B average fuel mileage [AVG. CONS.]:
Tripmeter B Average Speed [AVG. SPD.]
Displays the average speed since the tripmeter B was reset.
The average speed will be calculated based on the value displayed on the selected tripmeter B.
Display range: 0.0 to 299.0 km/h or 0.0 to 186.0 mph
|
|
To reset the tripmeter B average speed [AVG. SPD.]:
Tripmeter B Fuel Consumption [CONS.]
Displays the tripmeter B fuel consumption since the tripmeter B was reset.
Display range: 0.0 to 300.0 L (gal)
|
|
To reset the tripmeter B fuel consumption [CONS.]:
Tripmeter B Elapsed [ELAPSED]
Displays the tripmeter B elapsed since the tripmeter B was reset.
Display range: 00:00 to 99:59 (hours:minutes)
|
|
When “00:00” flashes, have your dealer check for problems.
To reset the tripmeter B elapsed [ELAPSED]:
Current Fuel Mileage [INST. CONS.]
Displays the current instant fuel mileage
Display range: 0.0 to 299.9 l/100 km (km/l, mpg or mile/L)
|
|
When “---.-” flashes, have your dealer check for problems.
Available Driving Distance [RANGE]
Displays the estimated distance you can travel on the remaining fuel.
Display range: 999 to 0 km (999 to 0 mile)
The indicated available driving distance is calculated based on driving conditions, and the indicated figure may not always be the actual allowable distance.
|
|
Battery Voltage [VOLTAGE]
Displays the current battery voltage.
Display range: 7.5 to 18.5 V
|
|
When “---.-” flashes, have your dealer check for problems.
Date [DATE]
Displays today's date.
|
|
Average Fuel Mileage [AVG. CONS.]
Displays the average fuel mileage since the average fuel mileage was reset.
Display range: 0.0 to 299.9 l/100 km (km/l, mpg or mile/L)
|
|
When “---.-” flashes, have your dealer check for problems.
To reset the average fuel mileage [AVG. CONS.]:
Fuel Consumption [CONS.]
Displays the fuel consumption since the engine was started.
Display range: 0.0 to 300.0 L or 0.0 to 300.0 gal
|
|
Elapsed Time [ELAPSED]
Displays operating time since the engine was started.
Display range: 00:00 to 99:59 (hours:minutes)
|
|
When “00:00” flashes, have your dealer check for problems.
Subtraction Trip [-TRIP]
Distance travelled is subtracted from a preset figure, since the subtraction trip was set up.
Display range:
1,607.3 to -1,609.0 km or 999.0 to -1,000.0 mile
The display locks at “-1609.0” km (“-1000.0” mile) when the read-out exceeds -1609.0 km (-1000.0 mile).
|
|
Default: 000
Blank
Display is blank.
|
|
ABS Function on the Rear Wheel [ABS RR]
Displays the selected status of the ABS function on the rear wheel [ABS RR].
|
|
Available settings: [ACTIVE]/[CANCEL]
Default: [ACTIVE]
To select the ABS function on the rear wheel [ABS RR]:
Honda Selectable Torque Control Level [HSTC]
Display the selected value of the Honda Selectable Torque Control level [HSTC].
|
|
Setting range: Level 1 to 7 or 0 (Off)
To select the Honda Selectable Torque Control level [HSTC]:
Wheelie Control Level [W]
Display the selected value of the wheelie control level [W].
|
|
Setting range: Level 1 to 3 or 0 (Off)
To select the wheelie control level [W]:
Rear Suspension Preload Mode [PRELOAD]
CRF1100A3/A4/D3/D4/DL4
Displays the selected status of the rear suspension preload mode [PRELOAD].
|
|
|
Status icon |
Riding condition |
|
|
Rider only |
|
|
Rider and luggage |
|
|
Rider and passenger |
|
|
Rider, passenger and luggage |
Default: Rider only
To select the rear suspension preload mode [PRELOAD]:
G Switch [G]
CRF1100D/D3/D4/DL4
Displays the selected status of the G switch [G].
|
|
Available settings: [ACTIVE]/[CANCEL]
Default:
The side stand indicator comes on when the side stand is put down. It goes off when the side stand is raised.
|
Side stand indicator |
Displays the ambient temperature.
|
Air temperature gauge |
Display range: -10 ºC to 50 ºC
Road heat and exhaust from another vehicle can affect the temperature reading when your vehicle speed is less than 30 km/h (19 mph). It may take several minutes for the display to be updated after the temperature reading has stabilized.
Cruise Control Set Speed
The speed set for cruise control is displayed.
|
Cruise control set speed |
To set the cruise control set speed:
To Reset the Tripmeter A [TRIP A], Tripmeter A Average Fuel Mileage [AVG. CONS.], Tripmeter A Average Speed [AVG. SPD.], Tripmeter A Fuel Consumption [CONS.] and Tripmeter A Elapsed [ELAPSED]
To reset the tripmeter A [TRIP A], tripmeter A average fuel mileage [AVG. CONS.], tripmeter A average speed [AVG. SPD.], tripmeter A fuel consumption [CONS.] and tripmeter A elapsed [ELAPSED], press and hold the ENT switch while page 1 is displayed or touch and hold the page 1 area.
|
|
To Reset the Tripmeter B [TRIP B], Tripmeter B Average Fuel Mileage [AVG. CONS.], Tripmeter B Average Speed [AVG. SPD.], Tripmeter B Fuel Consumption [CONS.] and Tripmeter B Elapsed [ELAPSED]
To reset the tripmeter B [TRIP B], tripmeter B average fuel mileage [AVG. CONS.], tripmeter B average speed [AVG. SPD.], tripmeter B fuel consumption [CONS.] and tripmeter B elapsed [ELAPSED], press and hold the ENT switch while page 2 is displayed or touch and hold the page 2 area.
|
|
To Reset the Average Fuel Mileage [AVG. CONS.]
To reset the average fuel mileage [AVG. CONS.], press and hold the ENT switch while page 3 is displayed or touch and hold the page 3 area.
|
|
|
Recommended topic(s) |
|---|
|
|
|
|
|
|